Pop-lock PL8140 Bedienungsanleitung
Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Pop-lock PL8140 herunter. Pop & Lock PL8140 User Manual Benutzerhandbuch
- Seite / 2
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Step 4: Wiring (there are multiple ways to run the wiring this is one suggestion)
Route the bullet connector side of the short wiring harness through one of the drain
holes at the bottom of the tailgate up to the power lock assembly. Connect it to the bullet
connectors of the power unit. Secure the wire with cable ties to prevent the wire from
getting pinched or in the way of the latch rods. Connect the other end to the long wire harness. Locate
this connector under the truck
so that it is accessible for tailgate removal. Run the long wiring cable along the factory wire
harness to the engine compartment
securing it with cable ties. Route wire into the driver’s compartment and to the driver side step sill (the plate you step on when getting
in and out of the truck). Use one of the factory’s rubber
grommets in either the firewall or along the floor pan. Cut a small slit in the
grommet or run the wire next to the grommet to allow the wire to pass through. It is recommended to seal around wire to prevent moisture
from entering the cab. Run the wire out of view to the step sill. Locate the tan with a yellow stripe wire and the grey wire. If testing the wire
to verify, all 2014 and newer Chevy/GMC Crew cabs the Lock and Unlock wires cannot be tested with a standard incandescent test light, you
will need to use a computer safe tester. Use the supplied wire taps to connect to theses two wires. At this point it doesn’t matter which
wire is tapped to the OEM wires. Test the operation of the lock (if the tailgate
lock works opposite of the door locks, disconnect the two
bullet connectors back by the power lock assembly, switch the leads of the wires, and reconnect the bullet connectors. This will make
the lock the same as the doors). Secure all the wiring and replace the removed trim pieces.
Installation
Instructions
Tailgate Lock
PL8140
Chevrolet/GMC
1500
2014 & Up
Tools Required: T35 Torx (Star) Bit/Driver
10mm Wrench
Pliers
Step 5: Shut the tailgate. Test the function of the key lock and power lock. The key lock will function different. To lock the tailgate,
rotate the key clockwise about 45 degrees and back to vertical. To unlock the tailgate, rotate the key counter clockwise about 45
degrees and back to vertical. The key will always be removed in the vertical position. If everything works, reinstall the access panel.
Package Contents: Power Lock Assembly, Cam, E-Clip
Long and Short Wire Harness
2 Wire Taps, 8 Cable Ties
Instructions
Step 1: Remove the torx (star) screws from the inside of the tailgate that hold the access panel in place and remove the access panel.
Step 3: Install the power lock assembly. Start by removing the handle
mounting bolt on the passenger side of the handle. Position the power lock
assembly so that one hole is over the plastic stud and the other is over the
mounting bolt hole. The arm on the slide bar should be positioned between the
white plastic locking toggle and near the arm of the cam, as shown in picture 4.
Reinstall the bolt and tighten.
Step 2: The cam on the back side of the factory lock cylinder needs to be replaced with the Pop and Lock cam. When doing this make
sure the factory lock cylinder is in the unlock position (key vertical). Start by removing the retainer clip located on the back of the lock
cylinder. Use a small flat head screw driver to lift the little tab on the retainer clip up and slide the retainer clip off of the lock assembly.
Remove the cam. Install the Pop and Lock cam onto the lock assembly so that the arm of the cam is positioned between the white
plastic locking toggle as shown in the picture. Install the provided e-clip in place of the OEM retainer clip (this e-clip and cam design
allows for some rotating play of the cam)
1
2
Weitere Dokumente für Für das Auto Pop-lock PL8140
Pop-lock PL8140 Bedienungsanleitung
(2 Seiten)
Verwandte Produkte und Handbücher für Für das Auto Pop-lock PL8140
(2 Seiten)
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.385 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern